The top flange type allows for space-saving and direct installation into the fixture body. Oil supply is made through drilled channels or pipe thread.
The new work supports are optimally protected against penetration of swarf by a metallic wiper edge and sealed against liquids.
All interior parts are made of stainless materials.
  

N-S041  |  Data sheet B1.9503

The new work supports are a further development of the work supports as per data sheet B 1.940. The most important differences are:
The new work supports are optimally protected against penetration of swarf by a metallic wiper edge and sealed against liquids.
All interior parts are made of stainless materials.

N-S040  |  Data sheet B1.9401

The program range of hydraulic accumulators has been revised and completed by new versions. The new program range comprises 4 sizes with adaptable gas preload.
All information see new data sheet F 9.601.
Hydraulic accumulators are used in hydraulic power workholding applications as energy accumulator for compensation of internal leakages or to compensate the volume in the case of temperature changes.

N-S039  |  Data sheet F9.601

The hinge clamp is a low-cost hydraulic clamping element with many installation and connecting possibilities. The special kinematics allow clamping nearly without side loads of workpieces which are very sensitive against deformation.
This line is designed for the direct connection to the machine hydraulics with a max. operating pressure of 70 bar.
2 sizes with a maximum clamping force of up to 7.0 kN are offered.

N-S038  |  Data sheet B1.8261

The mini hinge clamp is a low-cost hydraulic clamping element with many installation and connecting possibilities. The special kinematics allow clamping nearly without side loads of workpieces which are very sensitive against deformation.
This line is designed for the direct connection to the machine hydraulics with a max. operating pressure of 70 bar.
1 size with a maximum clamping force of 2.2 kN is offered.

N-S037  |  Data sheet B1.8262

The new work supports are a further development of the work supports as per data sheet B 1.950. The most important differences are:
The new work supports are optimally protected against penetration of swarf by a metallic wiper edge and sealed against liquids.
The venting for the spring area is universally connectable and can also be used for the connection of air sealing.
All interior parts and support plungers are made of stainless steel.
  

N-S036  |  Data sheet B1.9501

Inductive proximity switches are used for position monitoring. They are installed in the housing of the swing clamp. The control cap for activation of the proximity switches is connected to the clamping arm to enable permanent position monitoring of the clamping arm.

N-S035  |  Data sheet B1.8821

Position-flexible fixture clamps can additionally clamp and support a workpiece, which is already positioned and clamped in fixed stops, at unstable workpiece sections.
Due to their compact design they can be arranged in a very limited space. Fixture clamps are especially suitable for series manufacturing in automated mode.

N-S034  |  Data sheet I4.130

All swing clamps of this data sheet issue 9-08 (September 2008) were redesigned - with the objective to increase the clamping force or to use also longer clamping arms. The result is quite respectable:
=> up to 75% higher clamping force!
=> now 75% longer clamping arms can be used with the same clamping force!
  

N-S033  |  Data sheet B1.852

Due to the small dimensions at the effective point and the compact design clamping of workpieces with raised parts right next to the bore to be clamped is possible.
The bore clamp can be equipped with 3 different clamping inserts: with centring, with compensation and without centring.

N-S032 |  ROEMHELD information S008

The compact clamp particularly excels by its minimum dimensions. Due to the integrated pneumatic clamping monitoring it is possible to check the availability of the workpiece and the clamping pressure.
Two different cartridge types, each in four sizes, offer a high flexibility for the design of clamping fixtures.

N-S031 |  ROEMHELD information S010

The new swing clamps maintain the total clamping force by a patented self-locking device if hydraulic pressure is cut off or drops. Locking of the piston rod is made by a seperately-acting self-locking locking piston. Locking at the piston rod is positively. Actually there are two sizes with optional inductive or pneumatic position monitoring.

N-S030 |  ROEMHELD information S001

Completely pressed high-pressure hoses with nominal diameter 4 and 6 with mounted union nut.
The new data sheet F 9.361 replaces data sheet F 9.360, since the versions with pipe sockets with removable cutting ring and union nut are no longer allowed for safety reasons.

N-S028  |  Data sheet F9.361